| Hot Tank and mag complete engine w/final wash | $50 |
| Sonic Test | $135 |
| Bore and Hone w/torque plates | $170 |
| Full line hone w/studs (install studs, cut caps) | $110 |
| Trial assemble | $80 |
| Clearance for stroker | $50 |
| Deck block | $80 |
| R and R cam bearings | $35 |
| Performance Engine- Balance assembly | $35 |
| Heavy add 2pc to crank – 1.5hr | $160 |
| Hang pistons on rods/pins | $150 |
| SUBTOTAL | $1060 |
| Surface heads | $65 |
| Port and Polish heads | $500 |
| Performance three-angle valve job | $135 |
| Install guide liners 1st and 2nd | $80 |
| R and R guides cast HD | $32 |
| Cut/install hard seats in heads | $130 |
| Cut for PC Seals | $50 |
| Cut for big valves | $50 |
| Surface heads | $65 |
| CC first cylinder | $15 |
| SUBTOTAL | $1122 |
| Ferrea Custom made 2.02/1.60 stainless valves | $500 |
| .927 lightweight pins | $35 |
| Crower Springs 68305-1 | $90 |
| Sealed Power Rubber Type PC Seals ST2012 | $45 |
| Crower keepers 86107-1 | $45 |
| Nylen Guides 6850 | $45 |
| Manley Retainers 23645-16 | $60 |
| SUBTOTAL | $820 |
| JE custom forged aluminum pistons (Mazzolini) | $739 |
| ARP 8.0L head studs | $35 |
| ARP 4.06L main studs | $35 |
| ARP washers ARP200-8534 (Summit) | $25 |
| ARP ½-20 hex nuts ARP200-8637 | $25 |
| Dorman brass expansion plugs 560-023 | $18 |
| Mopar Performance 4" stroker crank P5007256 (Summit) | $340 |
| Clevite hardened rod bearings CB481H (Summit) | $90 |
| Clevite full groove main bearings MS1344P (Mancini) | $45 |
| Childs and Albert Dura Moly rings (Mazzolini) | $115 |
| SUBTOTAL | $1467 |
| Eagle H-beam connecting rods (or use SIR rods at approximately $300) | $500 |
| New Poly Hi-Performance Poly camshaft (or $100 for reground cam) | $200 |
| New Poly Hi-Performance solid lifters (or hydraulic) | $110 |
| Milodon small block windage tray 32230 (Mancini) | $47 |
| Melling hi-volume oil pump M72HV (Summit) | $49 |
| Mopar Performance hardened distributor drive small block (Summit) | $28 |
| Distributor drive bushing | $6 |
| Rollmaster billet timing set small block MRE1262 (Mancini Racing) | $100 |
| BHJ street dampner BHJMP-IB816 (Mancini Racing) | $160 |
| Flo-Kooler hi-flow water pump 1701 (Summit Racing) | $98 |
| Fel Pro full gasket set FS7734PT-2 | $99 |
| Blueprinted 1.5 or 1.6 ratio rocker set (hard chromed shafts, trued rockers, fully bushed w/lockdown nuts) |
$150 |
| SUBTOTAL | $1547 |
| Full engine assembly | $250 |